SSC-32 Servo Controller
Description -
This is the best servo controller value available. 32 channels of 1uS resolution servo control. Bidirectional communication with Query commands. Synchronized, or "Group" moves. 12 Servo Hexapod Gait Sequencer built in. MiniSSC-II emulation, like having 4 of them. Plus much more!
|
|
Part#
[
SSC-32
]
$39.95 USD
|
|
|
|
SSC-32 Upgrade - Atmega168 Pre-Programmed Chip
Description -
This is a drop-in replacement for the Atmega8 chip. If your SSC-32's IC chip has a large "V2" written on it, it is already the Atmega168 and you don't need this upgrade.
|
|
Part#
[
AM-168
]
$9.95 USD
|
|
|
|
DB9 Serial Data Cable - 6'
Description -
This cable is used with a Bot Board II or SSC-32 servo controller. Length is 6'.
|
|
Part#
[
DB9-02
]
$9.95 USD
|
|
|
|
Hitec 4Ch RC Set
Description -
FCC approved for use with surface vehicles (robots). 4 fully proportional channels. Includes transmitter, receiver and 2 servos.
|
|
Part#
[
HIT4-01
]
$113.99 USD
|
|
|
|
Hitec 6Ch RC Set
Description -
FCC approved for use with surface vehicles (robots). 6 fully proportional channels. Includes transmitter, receiver and 2 servos.
|
|
Part#
[
HIT6-01
]
$134.99 USD
|
|
|
|
|
|
Regulated Wall Pack - 6.0vdc 2.5amp
Description -
High quality 6vdc 2.5amp regulated wall pack perfect for powering servos. Includes several different styles of interchangeable snap-in wall adapters. Also includes replacement plug; requires soldering to change plug (see the plug change guide).
|
|
Part#
[
WP-02
]
$24.95 USD
|
|
|
|
|
|
USB-to-Serial Adapter Cable
Description -
FTDI USB-to-serial adapter cable. Drivers available here. This is the fastest and most stable USB-to-serial cable available. It's made by the same place that makes the FTDI chipset and has been proven to work well with all of our products.
|
|
Part#
[
USB2S-01
]
$29.95 USD
|
|
|
|
Single H-Bridge - HS-5745 Servo Amp
Description -
Control = R/C control 1.1mS - 1.5ms - 1.9ms
Channels = 1 (single motor controller)
Voltage = 4.8vdc - 6.0vdc
Continuous Current = ~2amps/6.0vdc (estimated)
Peak Current = 4.8amps/6.0vdc
Features = Can be used as a controller for a home brew "monster servo" gear head motor servo
Note: Hitec no longer attaches a heat sink on this device. You might want to add one.
|
|
Part#
[
SHB-01
]
$17.95 USD
|
|
|
|
V-Tail Mixer
Description -
This mixer allows you to control a differentially-steered vehicle with steering and throttle style control. With this mixer, you can use a pistol-grip style radio for your Battlebot.
|
|
Part#
[
MX-02
]
$15.95 USD
|
|
|
|
HFP-20 Digital Servo Programmer / Tester
Description -
This HFP-20 digital servo programmer allows you to reset factory defaults, preset and turn failsafe point on or off, change the direction and speed of rotation, adjust the deadband width, and change the end and neutral points. This device is required to change the Hitec digital servos from ~140° to 180° range capability. It is not required for the HSR-5995TG servo.
|
|
Part#
[
DSP-01
]
$154.99 USD
|
|
OUT OF STOCK
|
|
Servo Driver
Description -
This handy servo driver allows you to operate your servo or like device quickly and easily. Useful for aligning servos during construction of a robot or experimenting with motor drivers without needing to write a program. Includes center position light and cycle switch.
|
|
Part#
[
MX-04
]
$25.95 USD
|
|
|
|